Smartphone or Tablet WiFi Compatible RGB Controller w/ RF Touch Color Remote-Strip Modules Source

Custom LED Solutions
Colors Solutions
  • UV 365-395nm
  • Blue 410-440nm
  • Red
  • Green
  • RGB
  • IR 
  • Amber
  • Warm
  • Natural White 4500K
  • White 5500K
  • Cool White 6500K
  • Ice Cool 8500K
  • other colors

Voltage Solutions

  • DC 3-6V
  • DC 6-8V
  • DC 12-24V
  • DC 10-35V
  • DC 24-42V
  • AC 100-110V
  • AC 200-240V
  • AC 360V
  • AC 100-240V
  • other Voltage
Other Solutions
  • Waterproof  IP65-IP67
  • High Bright 100-130Lm/W
  • Dimming
  • Smart Remote:
  • – 2.4G – IR – WiFi – APP – 4G
  • Design:
  • – Colors – Voltage – Wattage 
  • – LED Chips – Heatsink 
  • – Pacakge  – Logo – Carton
  • – Fast Delivery – Freight Help 
  • LED Solutions Help
  • @ email tony@ledsolarwind.com

Smartphone or Tablet WiFi Compatible RGB Controller w/ RF Touch Color Remote


Applications:? Direct access color selection and functions with dimmable and speed controls
Function: Control 3 channel RGB LED products using wireless RF remote
Operating Voltage:??
Connection Mode:?? Common Anode (+)
Output:? Three CMOS open-drain outputs
Maximum Load Current:?? 24VDC – 6 Amps per channel (18 Amps total)
Output Power:? 216W @ 12V / 432W @ 24V
Control Method:? Wireless RF Remote Control – Frequency 2.4GHz
Batteries Required: Two AAA batteries
Modes: 20 Total (1 static single color and 19 dynamic color changing)
Operating Temperature: -25~60°C

Multi-Reciever Programming

The LDRF-RGB6-TC4 features transmitter to receiver keying to help eliminate interference from other nearby units. If you wish to control several receivers from a single transmitter, the receivers first must be re-programmed. The easiest and fastest way to re-program several receivers at once is to have them share a power supply or all plug in to a single power strip (Once programmed you can provide power as you would otherwise, sharing is only needed for the programming phase to ease the process — Re-programming can be done one device at a time also).

Programming Procedure:

  1. Wire all receivers to one power supply or power strip but don’t turn it on yet.
  2. With the power off, grab the remote.
  3. Turn on the power supply.
  4. Within 3 seconds of providing power press the LDRF-RGB6-TC2 Programming - Button 4 button once.

If programming was successful any connected light strings should blink three times.

NOTES:

1.) Do not scratch the sensing area. Do not disassemble, repair, or modify the device.
2.) Disconnect the power (adapter) before installing/removing this controller.
3.) Do not use this device near water, or moisture for indoor use only.
4.) This product should only be operated from the type of power source indicated on the label.
5.) When mutliple receivers share one remote, it’s possible for the patterns to visually drift apart over time. The single color modes are unaffected and remain synced.

RF Touch Color Remote Control

Typical Wiring Schematic

Modes List

RGB Light Bars & Strips Universal RGB Controllers and Dimmers
Numbers below represent the maximum number of units the controller can drive without the use of RGB amplifiers
RGB Amplifiers
Numbers below represent the maximum number of units the Amplifier can drive
Product Current Draw @ 12 Volt DC Product Length Max Run* LDRF-RGB6-TC4 RGB-A4 RGB-WA4 MRGB-A4 MRGB-A4-CPS RGBW-A6
RGB-1-DI 230ma 0.305m (1ft) 20 78 52 52 52 52 104
NFLS-RGB15-DI 202ma 0.5m (1.6ft) 20 89 59 59 59 59 118
NFLS-RGB30-DI 404ma 1m (3.3ft) 10 44 29 29 29 29 59
NFLS-RGB150-DI 1855ma 5m (16.4ft) 2 9 6 6 6 6 12
NFLS-RGB150X2 3295ma 5m (16.4ft) 1 5 3 3 3 3 7
NFLS-RGB150-KIT 1970ma 5m (16.4ft) 2 9 6 6 6 6 12
NFLS-RGB30X2-WHT 808ma 1m (3.3ft) 5 22 14 14 14 14 29
NFLS-RGBNW300X3-WHT 4700ma 5m (16.4ft) 1 3 2 2 2 2 5
NFLS-RGBWW300X3-WHT 3750ma 5m (16.4ft) 1 4 3 3 3 3 6
* Maximum number of light bars in one run (end to end) – for higher quantities, multiple runs back to the power supply, controller, or amplifier must be made to prevent excessive voltage drop Note: To determine the maximum number of any LED products on a single Power Supply – divide the total current capability of the power supply by the current draw of the LED product – then multiply that number by 0.8 (for 80% capacity)
Product Specifications
Amps 18.00 Amps Amps per Channel 6 Amps/CH
Battery Type 2 x AAA Controller Functions Color Wheel/Phone and Tablet App
DC Jack Type 5.5 Barrel Connector Radio Frequency 2.4 GHZ
Remote[1] Phone and Tablet App/Syncable Standards And Certifications CE/FCC/ROHS Compliant
Suitable for Vehicles Yes Type RGB Controller
Volts 12~24 VDC
Dimensions: 8.475cm(3.34″) x 4.45cm(1.75″) x 2.25cm(0.89″)