|Applications:?||Color selection, change, and chase with speed, direction and length control for accent lighting|
|Function:||Control SEDC-RGB series Light Strips using controller unit or RF remote|
|Operating Voltage:??||5 Volts DC|
|Connection Mode:??||Common Anode (+)|
|Output:?||2 SPI signals|
|Maximum Load Current:??||–|
|Static Power Consumption:?||2.2 Watts|
|Overall Size:?||(L)94 X (W)58 X (H)26 mm|
|Control Method:?||6 button on Controller Unit or wireless RF Remote Control|
|Batteries Required:||23A, 12V battery for Remote (included)|
|Modes:||99 Color chasing or changing|
Typical Wiring Schematic
- 1. Program Window
Indicate current running program numbered from 01-99 “HL” stands for auto loop mode. When in HL mode the display alternates between “HL” and the current program
- 2. Speed Window
Indicates current running running speed from 01-99. The greater the number the faster the speed and vice-versa.
- 3. Turn On/Stand By
Press this key to power the unit on, or switch it into standby mode. The display will show the running unit length value in standby mode.
- 4. Pause/Play
Toggle between Play and Pause. The display blinks with the current value when Pause mode.
- 5/6. Next/Previous Program
Jump to the next or the previous program.
- 7/8. Speed up/Slow down
Programs run faster when pressing “Speed up” and run slower when pressing “Slow down”. A 99 in the speed window indicates the top speed and ’01’ indicates the slowest. The speed may vary depending on what program is running.
- 9/10. Running unit length Increase/Decrease
Used to increase or decrease the program running unit length. The window will display a number starting with the letter ‘L’. This number will vary from 16-200 with a greater number corresponding to a longer unith length. This number is a relative value does not have a strict relation to the LED numbers. In some programs the running speed may drop when the unit length increases.
- 11. Remote Antenna
The distance of the remote control can be increased by pulling out this antenna.
- 12. Power Input
The power input socket is on the side of the unit (see 12 on the diagram). Power requirements for different models are listed below.
Model RGB-DC99 Power DC 12V/2A Polarity
- 13. Outputs
There are two output jackets on the bottom of the unit (see 13 on the diagram). Pin functions are listed below.
The model RGB-DC99 controller is designed to be used with the SEDC-RGB160 series Silicone Enlcosed RGB Flexible Light Strip. Control the sequence mode, chase length, and speed of 99 different dynamic chasing patterns from the RF Remote Controller or directly on the RGB Controller unit. The Dream-Color systems controls each RGB LED in the strip independently.
1.)VERY IMPORTANT: Supply voltage for Controller is 12 Volts DC, power with included 12VDC Power Supply, do not exceed
2.)VERY IMPORTANT: Supply voltage for SEDC-RGB series Light Strips is 5 Volts DC, 12 Volts will destroy the SEDC-RGB series LED Strip
3.) Connect according to the drawing below.
4.) + (plus) and – (minus) #IC buttons will only work when unit is off.
5.) Each Controller has a handheld Remote matched to it and will only work with it’s matched remote. One remote cannot operate multiple controllers.
6.) Strip can be trimmed down to length by cutting it every 2 LEDs. If this is done waterproofing accessories are required on end that was cut.
|1?||Full color forward flow||51||Green-cyan-green reverse|
|2||Full color reverse flow||52||Green-cyan-green-open|
|3||Full color open||53||Green-cyan-green-close|
|4||Full color open||54||Green-blue-green forward|
|5||3-color fade forward||55||Green-blue-green reverse|
|6||3-color fade reverse||56||Green-blue-green open|
|7||3-color fade open||57||Green-blue-green close|
|8||3-color fade close||58||Red-white-red forward|
|9||6-color forward comet||59||Red-white-red reverse|
|10||6-color reverse comet||60||Red-white-red open|
|11||6-color comet open||61||Red-white-red close|
|12||6-color comet close||62||Blue-white-blue forward|
|13||3-color forward||63||Blue-white-blue reverse|
|14||6-color reverse comet||64||Blue-white-blue open|
|15||3-color comet open||65||Blue-white-blue close|
|16||3-color comet close||66||Green-white-green forward|
|17||3-color fade||67||Green-white-green close|
|18||Red sandglass||68||Green-white-green open|
|19||Green sandglass||69||Green-white-green close|
|20||Blue sandglass||70||6-color forward fade in out|
|21||3-color sandglass||71||3-color forward fade in out|
|22||Red 2-way sandglass||72||Red drop|
|23||Green 2-way sandglass||73||Green drop|
|24||Blue 2-way sandglass||74||Blue drop|
|25||Blue 2-way sandglass||75||Yellow drop|
|26||6-color forward flow||76||Purple drop|
|27||6-color reverse flow||77||Cyan drop|
|28||6-color open||78||White drop|
|29||6-color close||79||7-color drop|
|30||3-color forward||80||Red drop with grounding|
|31||3-color reverse||81||Green drop with grounding|
|32||3-color open||82||Blue drop with grounding|
|33||3-color close||84||Blue drop with grounding|
|34||Red-purple-red forward||84||3-color sway|
|35||Red-purple-red reverse||85||6-color sway|
|36||Red-purple-red open||86||Red sway with grounding|
|37||Red-purple-red close||87||Green sway with grounding|
|38||Red-yellow-red forward||88||Blue sway with grounding|
|39||Red-yellow-red forward||89||White sway with grounding|
|40||Red-yellow-red open||90||3-color sway with grounding|
|41||Red-yellow-red open||91||Red stretch|
|42||Red-green-red forward||92||Green stretch|
|43||Red-green-red reverse||93||Blue stretch|
|44||Red-green-red open||94||Green drop with grounding|
|45||Red-green-red close||95||3-color stretch|
|46||Red-blue-red forward||96||Red ping-pong|
|47||Red-blue-red reverse||97||Blue ping-pong|
|48||Red-blue-red open||98||6-color ping-pong|
|49||Red-green-red close||99||Red & blue flash|
|50||Green-cyan-green forward||HL||Auto loop mode|
|Remote||Single Device Pairing||Standards And Certifications||CE/FCC/ROHS Compliant|
|Suitable for Vehicles||No||Type||RGB Controller|
|Dimensions: 13.71cm(5.4″) x 10.46cm(4.12″) x 5.9cm(2.32″)|