Description
LDRF-RGB4-A RGB Controller w/ RF Remote and Audio
Applications:? | Specific color selection or color change with speed control modes for accent lighting |
Function: | Control 3 channel RGB LED products using wireless remote |
Operating Voltage:?? | 12 Volts DC |
Connection Mode:?? | Common Anode (+) |
Output:? | Three CMOS drain-open output |
Maximum Load Current:?? | 4 Amps/channel (12 Amps total) |
Output Power:? | 144 Watts |
Overall Size:? | (L)114 X (W)64 X (H)25 mm |
Control Method:? | Wireless RF Remote Control |
Batteries Required: | 23A, 12V battery for Remote (included) |
Modes: | 13 total (7 static and 6 dynamic) see desc. below |
Operating Temperature: | -20~60°C |

NOTES:
1.) Only power with 12VDC Power Supply and connect to 12 Volt Light Strips or unit will be damaged. Our Compact 50Watt and 24 Watt Power Supplies will plug into DC IN jack on left side of unit. Our Enclosed Power Supplies can be direct wired to “+” and “-” terminals on removable Green connector on right side of unit.
2.) Wireless controller uses one 23A, 12V battery.
3.) Connect according to the above drawing and note that the Green Connectors can be unplugged from the unit.
4.) Red LED will come on when unit is receiving power, Green LED will flash when RF signal is received from handheld transmitter.
5.) UP and DOWN buttons will only work when unit is in one of the four color-changing (dynamic) modes.
6.) Each Controller has a handheld Remote matched to it and will only work with it’s matched Remote. One Remote cannot operate multiple Controllers.
7.) Controller can control a maximum of 30 meters of our Flexible RGB LED Strip. Over 30 meters, the Strips have to connect with an amplifier to reinforce the transmission of signal. Use one RGB Amplifier for every 30 meters of additional LED Strips.
8.) Do not exceed 80% of Power Supply capacity when calculating Power Supply size to use in your system.
9.) Suitable for automobile applications
RF Remote Control

Dimensions

Dimensions in millimeters (inches)
Typical Wiring Schematic

RGB Light Bars & Strips | Universal RGB Controllers and Dimmers Numbers below represent the maximum number of units the controller can drive without the use of RGB amplifiers | RGB Amplifiers Numbers below represent the maximum number of units the Amplifier can drive | Product | Current Draw @ 12 Volt DC | Product Length | Max Run* | LDRF-RGB4-A | RGB-A4 | RGB-WA4 | MRGB-A4 | MRGB-A4-CPS | RGBW-A6 |
---|---|---|---|---|---|---|---|---|---|
RGB-1-DI | 230ma | 0.305m (1ft) | 20 | 52 | 52 | 52 | 52 | 52 | 104 |
NFLS-RGB15-DI | 202ma | 0.5m (1.6ft) | 20 | 59 | 59 | 59 | 59 | 59 | 118 |
NFLS-RGB30-DI | 404ma | 1m (3.3ft) | 10 | 29 | 29 | 29 | 29 | 29 | 59 |
NFLS-RGB150-DI | 1855ma | 5m (16.4ft) | 2 | 6 | 6 | 6 | 6 | 6 | 12 |
NFLS-RGB150X2 | 3295ma | 5m (16.4ft) | 1 | 3 | 3 | 3 | 3 | 3 | 7 |
NFLS-RGB150-KIT | 1970ma | 5m (16.4ft) | 2 | 6 | 6 | 6 | 6 | 6 | 12 |
NFLS-RGB30X2-WHT | 808ma | 1m (3.3ft) | 5 | 14 | 14 | 14 | 14 | 14 | 29 |
NFLS-RGBNW300X3-WHT | 4700ma | 5m (16.4ft) | 1 | 2 | 2 | 2 | 2 | 2 | 5 |
NFLS-RGBWW300X3-WHT | 3750ma | 5m (16.4ft) | 1 | 3 | 3 | 3 | 3 | 3 | 6 |
* Maximum number of light bars in one run (end to end) – for higher quantities, multiple runs back to the power supply, controller, or amplifier must be made to prevent excessive voltage drop Note: To determine the maximum number of any LED products on a single Power Supply – divide the total current capability of the power supply by the current draw of the LED product – then multiply that number by 0.8 (for 80% capacity) |
Product Specifications | |||
---|---|---|---|
Amps | 12.00 Amps | Amps per Channel | 4 Amps/CH |
Controller Functions | Audio Input | Remote[1] | Radio Frequency/Single Device Pairing |
Standards And Certifications | CE/FCC/ROHS Compliant | Suitable for Vehicles | Yes |
Type | RGB Controller | Volts | 12~24V AC/DC |