LDIR-RGB3 RGB Controller with IR Remote-Strip Modules Source

Category:

Description

LDIR-RGB3 RGB Controller with IR Remote

Applications:?Specific color selection, custom color programming, or color change with speed control modes and dimming capabilities for accent lighting
Function:Program and save custom colors, dynamic color changing, dim and control 3 channel RGB LED products from 0~100% using PWM with remote
Operating Voltage:??5~24 Volts DC
Connection Mode:??Common anode (+)
Output:?(2x) 3 channel RGB wire
Maximum Load Current:??3 Amps/channel (9 Amps total)
Output Power:?216W @ 12V / 432W @ 24V
Overall Size:?(L)127 X (W)52 X (H)19 mm
Control Method:?Wireless IR remote control
Batteries Required:CR2025 battery for remote (included)
Modes:32 total (26 static and 6 dynamic)
Operating Temperature:-25~60°C

Typical Wiring Schematic

?

LDIR-RGB3: 12VDC RGB LED Controller

The model LDIR-RGB3 is a RGB controller with handheld Infrared Remote that can be used to program custom colors, control and dim any of our Red/Green/Blue (RGB) LED Light Bars and Light Strips. Several different static colors (including pure white) and dynamic color changing modes are directly selectable and adjustable on the IR remote. Up to six different custom colors can be programmed and saved on the six DIY buttons for direct selection.

NOTES:

1.) Only power with 5~24VDC power supply.
2.) Wireless controller uses one CR2025 battery.
3.) Connect according to the drawing below.
4.) QUICK and SLOW speed buttons will only work when unit is in one of the color changing (dynamic) modes.
5.) Controller can control a maximum of 48 meters of our Flexible RGB LED Strip. Over 48 meters, the strips have to connect with an amplifier to reinforce the transmission of signal. Use one RGB Amplifier for every 30 meters of additional LED Strips.
6.) Do not exceed 80% of Power Supply capacity when calculating Power Supply size to use in your system.

?

Controller Connections

IR Programmable Remote Control

RGB Light Bars & StripsUniversal RGB Controllers and Dimmers
Numbers below represent the maximum number of units the controller can drive without the use of RGB amplifiers
RGB Amplifiers
Numbers below represent the maximum number of units the Amplifier can drive
ProductCurrent Draw @ 12 Volt DCProduct LengthMax Run*LDIR-RGB3RGB-A4RGB-WA4MRGB-A4MRGB-A4-CPSRGBW-A6
RGB-1-DI230ma0.305m (1ft)203952525252104
NFLS-RGB15-DI202ma0.5m (1.6ft)204459595959118
NFLS-RGB30-DI404ma1m (3.3ft)10222929292959
NFLS-RGB150-DI1855ma5m (16.4ft)24666612
NFLS-RGB150X23295ma5m (16.4ft)1233337
NFLS-RGB150-KIT1970ma5m (16.4ft)24666612
NFLS-RGB30X2-WHT808ma1m (3.3ft)5111414141429
NFLS-RGBNW300X3-WHT4700ma5m (16.4ft)1122225
NFLS-RGBWW300X3-WHT3750ma5m (16.4ft)1233336
* Maximum number of light bars in one run (end to end) – for higher quantities, multiple runs back to the power supply, controller, or amplifier must be made to prevent excessive voltage drop Note: To determine the maximum number of any LED products on a single Power Supply – divide the total current capability of the power supply by the current draw of the LED product – then multiply that number by 0.8 (for 80% capacity)
Product Specifications
Amps9.00 AmpsAmps per Channel3 Amps/CH
Controller FunctionsCustom ColorRemote[1]Infrared (IR)/Multi Device Pairing
Standards And CertificationsCE/FCC/ROHS CompliantSuitable for VehiclesYes
TypeRGB ControllerVolts12~24 VDC